 |
Chinese RPD. This gun is a Pre-1986 dealer sample. A Korean War Bringback. Pitting may be caused from blood. Definitely in need of some restoration. |
 |
Chinese RPD barrel view |
 |
Chinese RPD belt feed entrence |
 |
Chinese RPD showing bottom view and ejection port |
 |
Chinese RPD showing right side of feed mechanism end belt ejection port |
 |
Bulgarian RPD showing style A of gas piston and gas regulator. Regulator can move to three differnt gas settings. |
 |
Bulgarian RPD showing style B gas piston and regulator housing |
 |
Bulgarian RPD showing style B gas piston and regulator housing |
 |
gas regulator, disassembled |
 |
Bulgarian RPD showing style A selector |
 |
Bulgarian RPD showing style B selector |
 |
Bulgarian RPD showing style A drum retaining spring and latch. This one had a broken spring which I replaced with an AK47 rear sight leafspring, ground to size. |
 |
Bulgarian RPD showing style A drum retaining spring and latch |
 |
Bulgarian RPD showing style B drum retaining spring and latch. |
 |
Bulgarian RPD showing style B drum retaining spring and latch |
 |
trigger group assembled to receiver. Note spring loaded latch and crosspin |
 |
Bulgarian RPD ejector |
 |
Bulgarian RPD front sight block, front view assembled |
 |
Bulgarian RPD front sight block, rear view, assembled |
 |
Bulgarian RPD front sight block with sight removed |
 |
xxx |
 |
xxx |
 |
Bulgarian RPD bolt assembly with extractor and firing pin |
 |
Bulgarian RPD with rear sight disassembled |
 |
Bulgarian RPD with rear sight assembled |
 |
Bulgarian RPD trigger housing top view stripped |
 |
Bulgarian RPD trigger housing, side view, stripped |
 |
Bulgarian RPD feed tray cover, assembled and partially disassembled |
 |
Bulgarian RPD feed tray assembled and disassembled |
 |
Bulgarian RPD feed tray partially disassembled |
 |
Bulgarian RPD rear sight, mounted |
 |
Bulgarian RPD showing feed tray cover latch |
 |
Chinese RPD showing refinsihed selecor and trigger assembly |
 |
xxx |
 |
xxx |
 |
Bulgarian RPD feed mechanism |
 |
Bulgarian RPD showing belt ejection port dustcover installed and disassembled |
 |
note subtle difference in Bulgarian (L) and Chinese (R) feed tray covers |
 |
Bulgarian RPD (L) belt feed assembled and Chinese (R) belt feed disassembled |
 |
Bulgarian RPD (L) belt feed assembled and Chinese (R) belt feed disassembled |
 |
bolt with rear locking lugsd eployed |
 |
recesses in receiver for locking lugs |
 |
assembly of trigger group to receiver, latch is raised to free crosspin |
 |
bolt locked, firing pin can contact primer |
 |
bolt unlocked, firing pin cannot contact primer |
 |
Chinese RPD, refinished and reassembled |
 |
handguard assembly. Even moderate firing will make the handguard too hot to touch and the heat will leach the oil from the laminated wood. |
 |
Chinese RPD, left side view after refinishing and reassembly |
 |
Chinese RPD, right side view after refinishing and reassembly |
 |
"U" style link engages the groove above cartridge rim. Cartridges are pushed forward out of the belt and directly into the chamber, unlike the RPK which pulls the rimmed 7.62x54R from the link before dropping it down and then pushing forward into chamber below. |
 |
"U" style 50 round sections of non-disintigrating belts are joined by a tab |
 |
cartridge keeps tab locked to connect two sections of "U" style 50 round non-disintigrating belts. |
 |
starter tab on front half of "U" style belt |
 |
"L" shaped belt retains cartridge case from rear. Final link in belt is solid and does not hold a cartridge |
 |
two linked 50 round belts in drum |
 |
"L" style 50 round sections of non-disintigrating belts are joined by a tab. There are two styles of tabs and recesses. the smaller tab fits both the small and the large recess, but the large tab only fits the large recess |
© 1994-2006 by T. Mark Graham. All Rights Reserved.